- It is currently Fri Mar 29, 2024 3:40 pm • All times are UTC + 10 hours [ DST ]
Anyone hear built a drip LA2a
Moderators: rick, Mark Bassett
4 posts
• Page 1 of 1
Anyone hear built a drip LA2a
Hi all, I'm just in the middle of wiring up my Drip LA2a. I am just using 1 cell do I need to hook up the switch as if I am using 2? Also I'm using the LED VU meter instead of the normal lamp. Just wondering where I can get the power from? Last question for tonight what size fuse do I buy for the IEC connector?
Andy Griffiths- onthebeatstudios & Andy's custom cables
http://www.onthebeatstudios.com
http://www.andyscustomcables.com
http://www.onthebeatstudios.com
http://www.andyscustomcables.com
- andygriffiths
- Regular Contributor
- Posts: 300
- Joined: Fri Apr 13, 2012 11:30 am
- Location: Brisbane
Re: Anyone hear built a drip LA2a
For the LED, 1/2 wave rectify a heater. Voltage then put the appropriate dropping resistor.Fuse wise 500ma or even 250ma should be more than adequate . if you,re only using a single cell a switch can be left out and wire directly
Alastair Reynolds
Broadcast Radio Engineer
Master of the Dark Arts (Broadcast)
Broadcast Radio Engineer
Master of the Dark Arts (Broadcast)
-
Alastair Reynolds - TRM Endorsed
- Posts: 475
- Joined: Mon Dec 04, 2006 1:51 pm
- Location: Sydney
Re: Anyone hear built a drip LA2a
Thanks Alastair, is it a slow blow fuse? Sorry for my dumbness
Andy Griffiths- onthebeatstudios & Andy's custom cables
http://www.onthebeatstudios.com
http://www.andyscustomcables.com
http://www.onthebeatstudios.com
http://www.andyscustomcables.com
- andygriffiths
- Regular Contributor
- Posts: 300
- Joined: Fri Apr 13, 2012 11:30 am
- Location: Brisbane
Re: Anyone hear built a drip LA2a
yeah, a T250mA should be OK, the in-rush current when the heaters are cold will be the biggest stress on the fuse , so a T /Timedelay/Slow-Blow fuse would be my choice here.
Fuse ratings are based on the continuous current that a fuse can carry without deformation of the fuse wire and premature failure. The fuse will open when the current exceeds approx. 1.6 times the rated current.
So a 1 amp fuse actually opens at 1.6A or there abouts. There may be some variations , but that's a good rule of thumb.
If a 1A fuse is carrying say 1.2 A, it will do it , but will eventually fail and when replaced with a 1A fuse will appear to be all OK.
Watch a fuse when you first apply power and heaters are cold or caps fully discharged if using a solid state rectifier, and see if the fuse wire flexes. if it does, it will probably fail prematurely.
Valve rectifiers, of course, come up gently and effectively "soft turn on" the HT.
Stay tuned for more obscure fuse -lore
Fuse ratings are based on the continuous current that a fuse can carry without deformation of the fuse wire and premature failure. The fuse will open when the current exceeds approx. 1.6 times the rated current.
So a 1 amp fuse actually opens at 1.6A or there abouts. There may be some variations , but that's a good rule of thumb.
If a 1A fuse is carrying say 1.2 A, it will do it , but will eventually fail and when replaced with a 1A fuse will appear to be all OK.
Watch a fuse when you first apply power and heaters are cold or caps fully discharged if using a solid state rectifier, and see if the fuse wire flexes. if it does, it will probably fail prematurely.
Valve rectifiers, of course, come up gently and effectively "soft turn on" the HT.
Stay tuned for more obscure fuse -lore
Alastair Reynolds
Broadcast Radio Engineer
Master of the Dark Arts (Broadcast)
Broadcast Radio Engineer
Master of the Dark Arts (Broadcast)
-
Alastair Reynolds - TRM Endorsed
- Posts: 475
- Joined: Mon Dec 04, 2006 1:51 pm
- Location: Sydney
4 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 7 guests