Just thought I would announce, that I have just nervously ordered what will be my first DIY attempt. The JLM BA4.
<gul[p> .....here I go. !!
Vic
- It is currently Thu Apr 18, 2024 10:00 pm • All times are UTC + 10 hours [ DST ]
JLM BA4
Moderators: rick, Mark Bassett
16 posts
• Page 1 of 1
JLM BA4
------------------
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
- Vic
- Registered User
- Posts: 231
- Joined: Sun Jul 11, 2010 11:50 am
- Location: Birrego, Nsw (6 hours to Sydney, 4 hours to Melbourne)
Re: JLM BA4
The only thing I can recommend .... for every component, double check its value, its location and orientation. Its so easy to rush and make a mistake and much much harder to work out where you went wrong later.
Good luck, you will enjoy the result
Michael
Good luck, you will enjoy the result
Michael
- Junction
Re: JLM BA4
I'll go ahead and book you into DIY anonymous Vic
Ben Moore
Harvest Recordings
Website: http://www.harvestrecordings.com.au
Facebook: http://www.faceback.com/harvestrecordings
Harvest Recordings
Website: http://www.harvestrecordings.com.au
Facebook: http://www.faceback.com/harvestrecordings
-
Ben M - Valued Contributor
- Posts: 1920
- Joined: Fri Jul 04, 2008 11:54 am
- Location: Sydney and Kangaroo Valley, NSW
Re: JLM BA4
No way, I'm just gonna try it once and that's it !!
------------------
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
- Vic
- Registered User
- Posts: 231
- Joined: Sun Jul 11, 2010 11:50 am
- Location: Birrego, Nsw (6 hours to Sydney, 4 hours to Melbourne)
Re: JLM BA4
Vic wrote:No way, I'm just gonna try it once and that's it !!
lol... Sure you will.
Danny Anderson
- danander11
- Registered User
- Posts: 225
- Joined: Sat Aug 21, 2010 8:16 pm
- Location: Sydney
Re: JLM BA4
Hi Michael,
Thanks for your advice, I will make sure to triple check everything !!!!
Vic
Thanks for your advice, I will make sure to triple check everything !!!!
Vic
------------------
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
- Vic
- Registered User
- Posts: 231
- Joined: Sun Jul 11, 2010 11:50 am
- Location: Birrego, Nsw (6 hours to Sydney, 4 hours to Melbourne)
Re: JLM BA4
Boy, I've made four of these bits, now on to the other bits.
It's kinda really enjoyable and at the same time, really frustrating.
Yes indeed
Vic
It's kinda really enjoyable and at the same time, really frustrating.
Yes indeed
Vic
You do not have the required permissions to view the files attached to this post.
------------------
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
- Vic
- Registered User
- Posts: 231
- Joined: Sun Jul 11, 2010 11:50 am
- Location: Birrego, Nsw (6 hours to Sydney, 4 hours to Melbourne)
Re: JLM BA4
Vic wrote:It's kinda really enjoyable and at the same time, really frustrating.
Vic
Well done Vic!
Yep definitely can be frustrating.
But also so many great kits around..and support..it can feel very rewarding.
Nice work!
Ben Moore
Harvest Recordings
Website: http://www.harvestrecordings.com.au
Facebook: http://www.faceback.com/harvestrecordings
Harvest Recordings
Website: http://www.harvestrecordings.com.au
Facebook: http://www.faceback.com/harvestrecordings
-
Ben M - Valued Contributor
- Posts: 1920
- Joined: Fri Jul 04, 2008 11:54 am
- Location: Sydney and Kangaroo Valley, NSW
Re: JLM BA4
I have FINALLY finished my JLM BA4.
Well, when I say I, I had so much help, that I should barely say "I". But I have learned so much about the process. In reflection I think I should have started with a single preamp, but it's done now and patched into the studio and all sounding might fine.
Well, when I say I, I had so much help, that I should barely say "I". But I have learned so much about the process. In reflection I think I should have started with a single preamp, but it's done now and patched into the studio and all sounding might fine.
You do not have the required permissions to view the files attached to this post.
------------------
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
- Vic
- Registered User
- Posts: 231
- Joined: Sun Jul 11, 2010 11:50 am
- Location: Birrego, Nsw (6 hours to Sydney, 4 hours to Melbourne)
Re: JLM BA4
Vic wrote:I have FINALLY finished my JLM BA4.
Well, when I say I, I had so much help, that I should barely say "I". But I have learned so much about the process. In reflection I think I should have started with a single preamp, but it's done now and patched into the studio and all sounding might fine.
great stuff
any chance we can get a wide shot.. I am about to start building new studio furniture...
Peter Knight
Cant ego loquemur Latine
http://www.peterknightmusician.com
Cant ego loquemur Latine
http://www.peterknightmusician.com
- Wiz
- Valued Contributor
- Posts: 1147
- Joined: Thu Dec 03, 2009 10:17 pm
Re: JLM BA4
HI Peter,
Here's a wide shot
Ta
Vic
Here's a wide shot
Ta
Vic
You do not have the required permissions to view the files attached to this post.
------------------
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
- Vic
- Registered User
- Posts: 231
- Joined: Sun Jul 11, 2010 11:50 am
- Location: Birrego, Nsw (6 hours to Sydney, 4 hours to Melbourne)
Re: JLM BA4
Thanks Vic
Beautiful
Beautiful
Peter Knight
Cant ego loquemur Latine
http://www.peterknightmusician.com
Cant ego loquemur Latine
http://www.peterknightmusician.com
- Wiz
- Valued Contributor
- Posts: 1147
- Joined: Thu Dec 03, 2009 10:17 pm
Re: JLM BA4
Looking good, what is the floorboard timber? real timber? click together type?
Barney Loveland
- Barney Loveland
- Frequent Contributor
- Posts: 523
- Joined: Mon May 09, 2005 5:28 pm
- Location: Melbourne
Re: JLM BA4
Hi,
The floor is the click together type. It's a really beautiful one, we get a lot of comments about that floor when people walk into the control room.
Vic
The floor is the click together type. It's a really beautiful one, we get a lot of comments about that floor when people walk into the control room.
Vic
------------------
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
- Vic
- Registered User
- Posts: 231
- Joined: Sun Jul 11, 2010 11:50 am
- Location: Birrego, Nsw (6 hours to Sydney, 4 hours to Melbourne)
Re: JLM BA4
Vic wrote:Hi,
The floor is the click together type. It's a really beautiful one, we get a lot of comments about that floor when people walk into the control room.
Vic
amazing.. can you link me to the floor please..
looks killer, and I might use it in my house.
cheers
Wiz
Peter Knight
Cant ego loquemur Latine
http://www.peterknightmusician.com
Cant ego loquemur Latine
http://www.peterknightmusician.com
- Wiz
- Valued Contributor
- Posts: 1147
- Joined: Thu Dec 03, 2009 10:17 pm
Re: JLM BA4
Hi,
I don't have the exact type written down.
I got it from this place, it was cheaper than you would think.
I'll have a look and see if I can find the invoice, and let you know.
But here is the link to the shop - http://www.lionkingflooring.com.au
Vic
I don't have the exact type written down.
I got it from this place, it was cheaper than you would think.
I'll have a look and see if I can find the invoice, and let you know.
But here is the link to the shop - http://www.lionkingflooring.com.au
Vic
------------------
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
Vic McEwan
http://www.vicmcewan.com
http://www.artsnswfellowship.com
http://www.cadfactory.com.au
- Vic
- Registered User
- Posts: 231
- Joined: Sun Jul 11, 2010 11:50 am
- Location: Birrego, Nsw (6 hours to Sydney, 4 hours to Melbourne)
16 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 2 guests