Turtlerock Forum

Has anyone had any experience with this from Factory Sound in South Melbourne.
http://factorysound.com/?SubCat=GEN-SOU ... e=FULLLIST

The couldn't provide any information on the material it was made from or density nor any charts. Apparently the get it from Joyce Foam Products
http://www.joyce.com.au/products.cfm?pr ... 20products

Couldn't find any info on website.

David,
Stay away from that stuff..Won't do absolutely anything to improve your acosutics and is expensive comparing to stuff that will actually help a lot. (like rockwool slabs wrapped in some fabric)
Funny how Factorysound says it will "get rid of standing waves" :0))
I bought some "acoustic" foam (more expensive, thicker and better looking than what you linked to) to line my entrance/hallway brick wall, just because I didn't have time to plaster/paint it..That's how "highly" i think (and many others) of its acoustic properties.. Once you start going up into Auralex and similar range of foam you MIGHT start hearing improvement. (don't get me wrog, you will hear the other foam as well, but it won't be an improvement)
IMO, any mineral wool with some rigidity to it, wrapped in some breathable fabric, will outperform any foam...for far less money.

simple question is it open cell foam or closed cell foam .?

only open cell foam works !

mattress foam is closed cell :(

rick wrote:
mattress foam is closed cell :(

:lol: so is this FS's standing wave "killer"

That foam will not, on its own, as presented, stop standing waves, period.

The manufacturer's website confirms that it is mattress foam..."Ideal For Rejuvenating Your Tired Mattress" (http://www.joyce.com.au/products.cfm?mo ... uct_id=107)

Turn around, point to an object in the distance, and run towards it.

The product being sold by factory sound isn't displayed on the website unfortunatly. It's also unfortunate when a salesperson dosn't know what they are selling and tries to belittle you while admitting as much.

My attention is noe focused more so on Senad's advice.

I have previously brought rockwool fron Pyrotek and coverd it in material with supprisingly good effect. I may try this but maybe make some frames which can be velcrod onto a wall then removed when needed.

Is rockwool still the standard these days?

I do also have Auralex foam panels and Bass Traps from a previous setup which I am sure will come in handy adition.

[EDIT]
Anyone have experiance with CSR Bradfors Soundscreen panels.
1350 by 430 cone in packs of 6 for $66 per pack.
http://www.ascentonline.com.au/html/pro ... ation.html

Apparently dencer than rockwoll although website stated they are made from rockwool.

My intent is to control acoustics within the room (Which ATM is brick/wood/glass and concreate) and not to sounproof.

They are Rockwool. This is what I made my (75mm) panels from, works a treat. Bunnings sell it too, probably cheaper.

David W wrote:Anyone have experiance with CSR Bradfors Soundscreen panels.
1350 by 430 cone in packs of 6 for $66 per pack.
http://www.ascentonline.com.au/html/pro ... ation.html

Apparently dencer than rockwoll although website stated they are made from rockwool.

My intent is to control acoustics within the room (Which ATM is brick/wood/glass and concreate) and not to sounproof.

rick wrote:simple question is it open cell foam or closed cell foam .?

only open cell foam works !

mattress foam is closed cell :(

Got reply back from Joyce.
The foam they supply to Factory Sound is Open Cell

Description: Polyester-Urethane Combustion Modified Grade S32/70CM (can anyone un-gibberish this for me).

Im also looking at making some bass traps. Will the particles from the rockwool do any harm to my lungs? Am I better off going with a polyester insulation? Also what type of fabric is best?

David W wrote:

rick wrote:simple question is it open cell foam or closed cell foam .?

only open cell foam works !

mattress foam is closed cell :(

Got reply back from Joyce.
The foam they supply to Factory Sound is Open Cell

Description: Polyester-Urethane Combustion Modified Grade S32/70CM (can anyone un-gibberish this for me).

its ok for making your room sound duller

mick_e wrote:Im also looking at making some bass traps. Will the particles from the rockwool do any harm to my lungs?

It should be ok but just to be safe.......try not to eat it.

Here is what i did from the advice of another engineer. We bulit up bass traps in the crners of the controll room using alternate layers of the green rock wool, 75 and 100, if my memory's right, with black plastic between each layer and a small timber baton nailed up the wall along the edge of each layer to anchor the plastic, and rock wool. We had two timber louver doors that we placed in each corner over the bass trap to give a good look and finish it off asthetically. A length of nice Indonesian Batik would do just as well depending on you decor.

yeah Dave,
Bradford's Soundscreen is the stuff I used all over my studio inside the walls and for acoustical treatment in CR and LR. You can see photos of the absorbers on my site..I was paying about $37 for a pack of 6 (2 years ago though) at 580mm width...but I did get 2 truckloads from the same place so the price was considerably lower than usual. The density is either 35 or 37kg/m3 can't remember now off top of my head. But this stuff WORKS!! I have 6 absorbers in my CR, (size of a rockwool slab + the frame around it) and the difference they made is quite astonishing. So $40 for rockwool + at the most $120 for timber and fabric and you have yourself 6, 1350X580 excellent wideband absorbers. It's not just those 6 that treat the whole room, but together with other stuff (corner super chunks, hangers above false ceiling etc..) they do excellent work. Mine are also mounted 100mm from the wall to provide wider band coverage (goes lower in the freq spectrum)
I also have big 2400X1200 mobile baffles in the live room, filled with the same stuff and 5 of those bring the RT60 value from about 1.4s down to about 0.8s or anywhere in between, depending on how you position them.