KRK V88's for sale.
Posted: Fri Mar 02, 2012 5:03 pmHi all,
A pair of American made KRK V88's for sale!!!
Cost:
$2,000 pair ONO (original approx $2, 500 each)
Description:
- Pair of high quality KRK V88 studio monitors with dual 8” LF drivers.
- Frequency response 39Hz to 23kHz, +2 dB.
- Two 8-inch woven Kevlar drivers wired in parallel, powered by a 160-watt amp and a 1.25-inch polymer dome tweeter fitted with an elliptical waveguide and driven by a 60-watt amp per enclosure.
- The rear panel Neutrik Combo XLR/TRS input connector is active and balanced, and handles an unbalanced signal as well.
- The crossover uses three-way active filters and a 2.3kHz crossover point.
- A three-position switch adjusts the HF shelving at 1 kHz to flat, ±1 dB.
- A three-position LF toggle has a -3dB corner frequency cut at 39, 47 or 55 Hz.
- An overall system gain/trim input sensitivity pot has a -30 dB to +6 dB range.
- The power switch is delayed and muted to avoid power-up/down thumps.
Condition:
Both are in great condition and have very minimal surface wear.
Reason for sale:
Downsizing! I have just moved and don't have room for these babies anymore. They're monitors that are better suited for mid-field monitoring.
Pickup only (Sydney)
Other Info:
V88 Technical Specifications:
Shielding Standard
Drivers 1-1/4"polymere dome (HF), 2x 8” woven Kevlar (LF)
Input XLR-1/4" TRS Combo
10k Ohm balanced
Pin1 + Sleeve = Ground
Pin2 + Tip = (+) High
Pin3 + Ring = (-) Low
Controls Input sensitivity (+6dB to –30dB variable)
3 position switch HF Adjust: +1dB, Flat, -1dB
3 position switch LF Adjust: -3dB @39Hz, @47Hz, @55Hz
Amplification Bi-amped: 60 watts (HF), 160 watts (LF)
Frequency response 39Hz to 21kHz, ±1dB
Maximum SPL @ 1m 112dB music, 115dB peak
Dimensions (H x W x D) 13-5/8” x 20”x 16-3/4” (34.6cm x 50.8cm x 42.5cm)
Shipping weight 57lbs (26kgs) each
A pair of American made KRK V88's for sale!!!
Cost:
$2,000 pair ONO (original approx $2, 500 each)
Description:
- Pair of high quality KRK V88 studio monitors with dual 8” LF drivers.
- Frequency response 39Hz to 23kHz, +2 dB.
- Two 8-inch woven Kevlar drivers wired in parallel, powered by a 160-watt amp and a 1.25-inch polymer dome tweeter fitted with an elliptical waveguide and driven by a 60-watt amp per enclosure.
- The rear panel Neutrik Combo XLR/TRS input connector is active and balanced, and handles an unbalanced signal as well.
- The crossover uses three-way active filters and a 2.3kHz crossover point.
- A three-position switch adjusts the HF shelving at 1 kHz to flat, ±1 dB.
- A three-position LF toggle has a -3dB corner frequency cut at 39, 47 or 55 Hz.
- An overall system gain/trim input sensitivity pot has a -30 dB to +6 dB range.
- The power switch is delayed and muted to avoid power-up/down thumps.
Condition:
Both are in great condition and have very minimal surface wear.
Reason for sale:
Downsizing! I have just moved and don't have room for these babies anymore. They're monitors that are better suited for mid-field monitoring.
Pickup only (Sydney)
Other Info:
V88 Technical Specifications:
Shielding Standard
Drivers 1-1/4"polymere dome (HF), 2x 8” woven Kevlar (LF)
Input XLR-1/4" TRS Combo
10k Ohm balanced
Pin1 + Sleeve = Ground
Pin2 + Tip = (+) High
Pin3 + Ring = (-) Low
Controls Input sensitivity (+6dB to –30dB variable)
3 position switch HF Adjust: +1dB, Flat, -1dB
3 position switch LF Adjust: -3dB @39Hz, @47Hz, @55Hz
Amplification Bi-amped: 60 watts (HF), 160 watts (LF)
Frequency response 39Hz to 21kHz, ±1dB
Maximum SPL @ 1m 112dB music, 115dB peak
Dimensions (H x W x D) 13-5/8” x 20”x 16-3/4” (34.6cm x 50.8cm x 42.5cm)
Shipping weight 57lbs (26kgs) each